You’ve probably been there. It’s 11:30 PM, you just unboxed that sleek, wooden-style Jall clock, and now you’re staring at three buttons on the back like they’re a bomb you need to defuse. Why does the time keep disappearing? Why is the temperature reading in Celsius? And why, for the love of all things holy, won't the alarm stop beeping?
Honestly, the jall alarm clock manual is one of those things people toss immediately and regret five minutes later. These clocks look minimalist and gorgeous, but their interface is... let's call it "efficient." It relies on long presses and short clicks that aren't exactly intuitive. If your clock is currently flashing at you or going dark every ten seconds, don’t worry. You haven't broken it. It's just doing exactly what it was programmed to do—you just need to know the "secret" handshakes to change it.
The Mystery of the Disappearing Display
This is the number one complaint. You set the clock, walk away, and a minute later the screen is black. You tap the table, and it pops back on. Most people assume the batteries are dying or the unit is defective.
It's actually a feature called Sound Control Mode.
Basically, the clock is trying to save energy (or keep your room dark) by only turning on when it hears a noise louder than 60 decibels. To fix this, look for the DOWN button on the back. Tap it once. You’ll see either "--:Sd" or "on:Sd."
- on:Sd means the display will turn off to "sleep" until it hears a sound.
- --:Sd means the display stays on permanently.
You want the one with the dashes. If you see "on:Sd," you're going to be clapping at your nightstand every time you want to check the time in the middle of the night. It’s annoying. Turn it off.
Setting the Time Without Losing Your Mind
Ready to actually set the time? You'll need the SET button. Don't just tap it—you have to hold it down for about two or three seconds until the year starts flashing.
👉 See also: Our Solar System with Diagram: Why Everything You Learned in School is Likely Wrong
- Use the UP and DOWN buttons to find the right year. Tap SET to confirm.
- Now the month will flash. Adjust it, tap SET.
- Do the same for the day.
- Finally, you'll reach the time setting.
Here is a pro tip: pay attention to the little dot in the top left corner of the screen. That’s your PM indicator. Jall clocks don’t usually have an "AM" light; if the light is off, it’s morning. If it’s on, it’s afternoon. If you ignore this, your alarm is going to go off at 6:00 PM while you’re making dinner instead of 6:00 AM when you actually need to wake up.
Switching to 12-Hour or 24-Hour Format
While you are in the time setting mode, you'll eventually see a choice between "12H" and "24H." Most people in the States prefer 12H, but if you like military time, 24H is there for you. Just tap the UP or DOWN button to toggle between them before hitting SET one last time to finish.
Managing the Triple Alarms
One thing that makes the Jall stand out is that it gives you three separate alarms (A1, A2, and A3). This is great if you have a partner who wakes up at a different time, or if you’re the type of person who needs a "warning" alarm before the real one.
To set them, tap the SET button (short presses this time) until you see "--:A1."
- The dashes mean the alarm is OFF.
- Tap the UP button to change it to "on:A1."
- Once it says "on," hold the SET button down to enter the time-setting mode for that specific alarm.
Repeat this for A2 and A3 if you need them. If you accidentally turned on all three and you're wondering why the clock won't stop screaming at you every 15 minutes in the morning, just navigate to A2 and A3 and use the UP button to turn them back to "--:A2" and "--:A3."
The Infamous "E" or Weekday Mode
Have you ever had your alarm fail to go off on a Monday? Or worse, had it wake you up at 6:00 AM on a Saturday? That’s likely because of the Weekday Mode setting.
While you're clicking through the menu, you might see "--:E" or "on:E." This stands for "End" (referring to the weekend).
- on:E means the alarm will only ring Monday through Friday.
- --:E means the alarm will ring every single day, including Saturday and Sunday.
I've seen so many people get caught by this. They think they've set a daily alarm, but because they have "on:E" selected, they oversleep on Saturday morning for their kid's soccer game. Check this setting twice.
Temperature and Humidity: Why Is It Wrong?
The Jall clock has a built-in sensor for temperature and humidity. It's cool, but it isn't a lab-grade hygrometer. Because the sensor is inside the wooden-style casing near the electronic components, it can sometimes run a few degrees warmer than the actual room temperature.
🔗 Read more: Radar for Wheeling WV: Why Your Weather App Always Seems Confused
To switch between Celsius and Fahrenheit, simply press and hold the UP button for a couple of seconds while in the normal time display mode. It should toggle instantly.
If your humidity reading seems stuck, try moving the clock away from a drafty window or a heater. The sensor needs a bit of stable airflow to give you a semi-accurate reading.
Brightness Control for Light Sleepers
The LED display on these clocks can be incredibly bright—like "landing strip" bright. Fortunately, Jall built in a brightness adjustment.
Hold down the UP button for a few seconds. You’ll see "L1," "L2," or "L3" appear.
- L3 is the brightest setting.
- L1 is the dimmest.
Interestingly, many models also have an automatic dimming feature that kicks in between 6:00 PM and 7:00 AM. If you find the clock is too dim during the day, you might just need to manually bump it back up to L3.
Powering the Beast: Batteries vs. Plug
Here is the most important piece of advice you will get today: Do not rely on batteries.
The jall alarm clock manual technically says you can use 4 AAA batteries, but if you do, the clock will probably die in about 48 to 72 hours. These LED displays are power hogs. The battery compartment is really only intended for "emergency backup" during a short power outage.
Always use the provided USB power cable and a 5V/500mA-1000mA power adapter. If you’ve lost the brick that came with it, a standard phone charger usually works fine. Just make sure it's plugged into a wall outlet if you want the screen to stay on and the time to remain accurate.
Resetting Everything
Sometimes the software just hangs. Maybe the screen is frozen, or the buttons aren't responding. In the back, there’s usually a tiny hole labeled RESET. Take a paperclip, poke it in there for a second, and the clock will reboot to its factory settings. You'll have to redo the time and alarms, but it usually clears up any weird glitches.
Quick Fix Checklist
- Screen goes dark? Turn off "on:Sd" (Sound Control).
- Alarm didn't go off? Check the PM dot and the "on:E" (Weekday) setting.
- Clock is too bright? Adjust the "L" level by holding the UP button.
- Dying every two days? Use the USB cable, not batteries.
Actionable Next Steps
To get your Jall clock perfectly calibrated right now, start by plugging it into a stable wall outlet rather than a computer USB port. Immediately disable the Sound Control Mode (look for --:Sd) so you aren't forced to shout at your clock just to see the time. Finally, double-check your PM indicator dot to ensure your morning wake-up call doesn't turn into an evening surprise. If the display still feels too bright for sleep, cycle through the brightness levels until you hit L1.